TrustSeal Verified

IndiaMART Verified Exporter

New Items

Elastically Coupled Beam Apparatus - (SISECB-05)

Elastically Coupled Beam Apparatus - (SISECB-05)
Apparatus consists of a three parallel bar suspension system with elastic beam at their upper and lower ends. The upper ends of the two outer suspension rods are tied to a vertical wooden board while central suspension rod may be tied to the center of another elastic beam supported at two outer ends only. Apparatus to be supplied should be complete with a supporting stand and a set of weights.

Portal Frame Apparatus - (SISPFA-10)

Portal Frame Apparatus - (SISPFA-10)
Apparatus made up of M.S. plate of rectangular section of 3mm thick X 40cm wide. Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. The size of portal will be 40cm X 60 cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus. Apparatus will be supplied complete with a supporting stand and a set of weights.

Shear Centre Apparatus - (SISSCA-08)

Shear Centre Apparatus - (SISSCA-08)
Apparatus consists of sturdy base frame and Channel, Equal angle, Semicircle and Z-Section are supplied with apparatus. Standard length of each of the four sections in M.S. is supplied. Each is provided with end clamp for fixing to the rigid bracket. A special load hanger is provided so as to change the load position so that with the help of two dial gauges the vertical plane of Shear centre for the particular section can be determined. 
Range of Experiments Determination of the vertical plane of shear center for different cross sections commonly used for structures.

Jaw Crusher - (MJC-01)

Jaw Crusher - (MJC-01)
This is a primary crusher and sometimes used as a secondary crusher too. It is used for size reduction of minerals, ores, chemicals, Ferro-alloys (except low carbon Ferro-chrome) Reduction ratio is 1:4 to 1:6 Body: Sturdy, M.S. Shaft: EN-8 
Jaws: 10-12% Mn-steel. 
Size available: *3" X 5", *5"X 9", 9" X 12", 10" X 16", 12" X 20"

Compression Testing Machine (4 Pillars Type) - (SICCCTM-05)

Compression Testing Machine (4 Pillars Type) - (SICCCTM-05)
Compression Testing Machine - 4 Pillars Nut Type Model, complete with Single Pressure Gauge & Self Made Motor, 440 ‘V’ Load Frames: Available in 50 Tons, 100 Tons, 150 Tons, 200 Tons, 300 Tons, 500 Tons. Available: Hand Operated & Electric cum Hand Operated in Welded & Nut Type Model

Additional Information:
  • Item Code: SICCCTM-4P05

Compression Testing Machine (2 Pillars Type) - (SICCCTM-04)

Compression Testing Machine (2 Pillars Type) - (SICCCTM-04)
Compression Testing Machine - 2Pillars Nut Type Model, complete with Single Pressure Gauge & Self Made Motor, 440 ‘V’ Load Frames: Available in 100 Tons, 150 Tons, 200 Tons. Model Available: Hand Operated & Electrically cum Hand Operated

Additional Information:
  • Item Code: SICCCTM-2P04

Compression Testing Machine (Channel Type) - (SICCCTM-03)

Compression Testing Machine (Channel Type) - (SICCCTM-03)
Compression testing machine - channel type model, complete with single pressure gauge & self made motor, 440 ‘v’ load frames: available in 100 tons, 150 tons, 200 tons. Models available: hand operated & electric cum hand operated

Additional Information:
  • Item Code: SICCCTM-CT03

Victor Mayer Apparatus

Victor Mayer Apparatus
a) Victor Meyer’s Apparatus Complete with Outer and Inner tube 
b) Victor Meyer’s Apparatus Spare Outer Jacket 
c) Victor Meyer’s Apparatus Spare Inner tube

Viktor Meyer apparatus is the standard laboratory method for determining the molecular weight of a volatile liquid

Additional Information:
  • Item Code: SILGVMA-001

Basic Concrete Testing Kit

Basic Concrete Testing Kit
Shambhavi impex offers a complete package of basic concrete testing kit at very exciting prices. our complete package include below products-
  • Compression Testing Machine (CTM) - 1No.

    SpecificationsCTM
    TypeChannel Type, Welded
    Capacity100 Ton
    OperationHand Operated
    Pressure GaugeSingle
    PowerSelf made Motor, 440 V

  • Slump Test Apparatus - 1 No. As per IS: 7320, BS 1881. It is used for the determination of the consistency of freshly mixed concrete, where the maximum size of the aggregate does not exceed 38mm.
    Specification: The Apparatus consists of one slump cone with handles and foot pieces. The slump cone has internal dimensions 20cm. dia at base 10cm. top dia. and 30cm height. Foot pieces can be fixed to the clamps on the base plate.
    The base plate has lifting handle for easy transportation. One graduated steel rod 16mm dia x 600mm long, rounded at one end and graduated in mms, is also supplied.

  • Cube Moulds - 6 Nos. As per IS : 516. Made of Cast Iron (Non ISI). Size: 150mm X 150mm X 150mm. These are used for casting cement concrete test specimens for carrying out compressive strength tests. These are available in different sizes and are made according to Indian and British Standards.
    Specification: For the metric size cube moulds, the faces are machined flat to +/-0.02mm accuracy and finished to within 0.02mm. For the inch size moulds, the faces are machined flat to +/-0.01 inches and finished to within 0.01 in. All moulds are supplied complete with base plate.

Trowel - 1 No. As per IS: 4031.  A Trowel is used for digging, smoothing, or otherwise moving around small amounts of viscous or particulate material. The dimension is about 100 to 150mm long steel blade with straight edges.

Jaw Crusher

Jaw Crusher

Approx. Rs 65,000 / Piece

  • Minimum Order Quantity: 1 Piece
  • Brand: Shambhavi IMPEX

This is a primary crusher and sometimes used as a secondary crusher too. It is used for size reduction of minerals, ores, chemicals, Ferro-alloys (except low carbon Ferro-chrome) Reduction ratio is 1:4 to 1:6
  • Body: Sturdy, M.S.
  • Shaft: EN-8
  • Jaws: 10-12% Mn-steel.
  • Size available: *3" X 5", *5"X 9", 9" X 12", 10" X 16", 12" X 20"

Additional Information:
  • Item Code: MJC-01

Ball Mill

Ball Mill
Ball Mill is suitable for grinding minerals, ores, chemicals, paints and pigments, soft and permanent magnetic material like Barium ferrite and alnico. Type of the mill can be Batch or Continuous. Grinding can be wet or dry. Material of Construction: It can be M.S., Stainless steel 304/316. Capacity will be depend on your material characteristics, moisture content, feed and product size desired. All the mills are sturdy with suitable bearings. Size of the mill: It can be from 200 mm x 200 mm to 2000 mm x 2000 mm. HP can vary from 1 to 75 hp

Additional Information:
  • Item Code: MBM-01

Laboratory Equipment

Laboratory Equipment
Shambhavi Impex offers a complete line of laboratory glassware including Cork Boring Machine, Absorption Tube, Cork Roller, Absorption Tube, U-Form, Crucible Gooch, Analytical Balance, Battery Charger, Deflagrating Spoon Dissectors, Measuring / Filtering / Distillation Flask, Masses Set and more items. These are offered in various standards and sizes to meet the needs of buyers. All our glassware is offered in safe packaging and we cater to bulk requirements efficiently. Known for competently priced items and timely delivery we supply glassware for laboratories as per bulk buyer’s request

  • Autoclave 
  • Balances 
  • Centrifuges 
  • Furnaces 
  • Heating Mantles 
  • Hot Plates 
  • Environmental Test Chamber 
  • Incubators 
  • Ovens 
  • Stirrer 
  • Water Bath 
  • Water Still 
  • Analytical Lab Equipment 

Vertical Autoclave

Vertical Autoclave
  • Application: Laboratory
  • Material: Stainless Steel
  • Shape: Vertical

Constant Temperature Water Bath - (IWB-004)

Constant Temperature Water Bath - (IWB-004)
  • Temperature range : 5 degree C above ambient to 99 degree C
  • Accuracy : +/- 0.5 degree C
  • Operation voltage: 230V
  • Power source type: AC
  • Rating: 1.5-2.5 KW

We are leading manufacturer and exporter of Constant Temperature Water Bath - (IWB-004) and our product is made up of good quality.

Double walled construction, the inner chamber is made of stainless steel and outer body made of mild steel duly powder coated. 

The gap between the two walls filled with glass wool insulation. 

Instructions:-
  • Temperature range 5°C above ambient to 99°C accuracy +/- 0.5°C. 
  • Fitted with immersion type heater. 
  • Digital temp. Controller cum indicator. 
  • Operating on 230V AC. 
  • Fitted with a circular pump with a stirrer.

Working size In inchesRating
12" x 10" x 8"1.5 KW
14" x 12" x 10"2.0 KW
18" x 14" x 12"2.5 KW

Stirres - (SILGST-001)

Stirres - (SILGST-001)
  • Stirres - (SILGST-001)
  • Stirres - (SILGST-001)
  • Packaging Type: Box
  • Brand: Shambhavi Impex
  • Material: PTFE
  • Code: SILGST-001

a) Stirrer (Borosilicate Glass) 1) PTFE Bladed Stirrers i. Shaft dia 6 mm Shaft Length 450 mm to Pass through 19/26 socket Blade width 50 mm Curved to Suit Flask 500 ml ii. Shaft dia 6 mm Shaft Length 450 mm to Pass through 24/29 socket Blade width 75 mm Curved to Suit Flask 1000 ml iii. Shaft dia 8 mm Shaft Length 600 mm to Pass through 34/35 socket Blade width 100 mm Curved to Suit Flask 2000 ml iv. Shaft dia 8 mm Shaft Length 600 mm to Pass through 34/35 socket Blade width 125 mm Curved to Suit Flask 5000 ml v. Shaft dia 10 mm Shaft Length 750 mm to Pass through 19/26 socket Blade width 150 mm Curved to Suit Flask 10000 ml vi. Shaft dia 10 mm Shaft Length 750 mm to Pass through 55/44 socket Blade width 200 mm Curved to Suit Flask 20000 ml 2) Stirrer Guides Socket 19/26.29/32 Cone 19/2629/32 b) Stirrers (Plastic) These stirrers are very useful for stirring different solutions in the laboratory. These stirrers prove to be tough and long lasting.

Elastic Properties of Deflected Beam Apparatus - (SISEPD-06)

Elastic Properties of Deflected Beam Apparatus - (SISEPD-06)
Apparatus consists of a mild steel beam 2.5cm X 3mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. One of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. At the other end also a known moment can be applied. Vertical loads can be applied at various points along the span of the beam. A Dial gauge with 25mm travel ( with a magnetic base) may be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights

Water Still Electrical Table Pattern Barn Stead Type - (LSIW

Water Still Electrical Table Pattern Barn Stead Type - (LSIW
Salient Features & Construction : Doubled walled Water Still (Barnstead Type) is made up of Outer MS powder coated and Inner tank made of SS. The gap in between is filled with glass wool. All the fittings such as condenser, top, and outer chamber are made up of Stainless Steel. The raw water is first made to pass around the tubes in the condenser, where it gets heated neatly to the boiling point thus economizing the heating energy . The evaporators are fitted with a set of totally immersed long life heating elements and are easily removable. A convenient drain valve is provided for flushing and easy accessibility to the entire evaporating chamber. The water still is fitted with special immersion element (ISI Marked) with automatic ejection device which stops working in the case of failure of water supply. Supplied with cord and plug to work on 220/230 volts A.C. supply. Operation: The preheated water then passes out of the condenser, gives may out to the gaseous and volatile Impurities in the atmosphere with the help of a special device incorporated herein and finally enters and boiling pan for distillation. The inlet water passing into the stills flows around and outside of the condenser tubes where it becomes per-heated nearly to the boiling point. 
Applications : These water distillation plants have been designed to meet with the requirements of best quality of distilled water. These are best suitable for removing all types of impurities Organic, Inorganic, Gaseous, Bacterial and Pyrogenic leaving a final pure distillate.

B.O.D Incubator (GMP Model) - (SILBODG-06)

B.O.D Incubator (GMP Model) - (SILBODG-06)
Double walled construction fully made of St. Steel inner mirror finished & exterior matte finished . The gap between the two walls filled with glass wool insulation. Cooling is by hermetically sealed compressors with CFC free refrigerant. Supplied with S.S shelves.
Temperature Controlled by Microprocessor based Digital Temp Controller with sensor.Temperature Range : 5°C to 60°C. accuracy ±0.5°C

CapacityInternal Dimensions(W x D x H)
3.0 Cu ft 90 ltr45 x 40 x 50 cms
6.0 Cu ft 170 ltr50 x 50 x 70 cms
10.0 Cu ft 280 ltr55 x 55 x 90 cms
12.0 Cu ft 330 ltr60 x 60 x 90 cms

Optional Accessories
  • Illumination by fluorescent tube 3 Nos
  • Cyclic Digital Timer for fluorescent tube
  • Rs 485 PC communication with Software Meta Logger
  • Single Channel Data logger with printing arrangement

B.O.D.Incubator - (SILBOD-05)

B.O.D.Incubator - (SILBOD-05)
Double walled construction inner chamber made of st. Steel and exterior made of G. I. Sheets powder coated. The gap between the two walls filled with glass wool insulation . Cooling is by hermetically sealed compressors with CFC free refrigerant. Supplied with S. S shelves. 
Temperature controlled by microprocessor based digital temp controller with sensor. Temperature range : 5°C to 60°C. accuracy ±0. 5°C

CapacityInternal Dimensions(W x D x H)
1.5 Cu ft     45 ltr35 x 35 x 35 cms
3.0 Cu ft     90 ltr45 x 40 x 50 cms
6.0 Cu ft     170 ltr50 x 50 x 70 cms
10.0 Cu ft     280 ltr55 x 55 x 90 cms
12.0 Cu ft     330 ltr60 x 60 x 90 cms

Optional Accessories
  • Illumination by fluorescent tube
  • Cyclic Digital Timer for fluorescent tube
  • Rs 485 interface PC communication with Software Meta - Logger
  • Single Channel Data logger with printing arrangement

Bacteriological Incubator (Memmert Type ) - (SILBIM-03)

Bacteriological Incubator (Memmert Type ) - (SILBIM-03)
Triple walled in construction inner chamber made of Mild Steel/ St. Steel and exterior made of G.I Sheets Powder coated. The gap between the two walls filled with glass wool insulation. Heating elements fitted on the two side of the incubator. A forced Air Circulating System with fan for better uniformity of temperature. Inner glass door and exterior metal door with magnetic gasket and lock.
Temperature Controlled by Electronic Digital Temp. Controller cum indicator.Temp Range : 5°C above ambient to 60°C.

Chamber sizeNo of Shelves
12" x 12" x 12"2
14" x 14" x 14"2
18" x 18" x 18"3
18" x 18" x 24"4
24" x 24" x 24"4
24" x 24" x 36"5

Optional Accessories
  • Electronic Digital Timer Range 0 to 999 minutes
  • S.S wiremesh shelves
  • Single Channel Data Logger with printing arrangement
  • RS 485 for PC communication with software Meta - Logger

Incubator Cum Oven - (SILICO-02)

Incubator Cum Oven - (SILICO-02)
Double walled construction inner chamber made of mild steel/ st. steel & exterior made of G.I. sheets powder coated. The gap between the two walls filled with glass-wool insulation. 
Temperature controlled by thermostat or by digital temperature indicator. Temp range: 5°c above ambient to 100°c.
Chamber size : 12" x 12" x 12"
14" x 14" x 14"

Bacteriological Lab Incubator (GMP Model) - (SILBIG-04)

Bacteriological Lab Incubator (GMP Model) - (SILBIG-04)
Double walled construction fully made of St. Steel. The gap between the two walls filled with glass wool insulation. Supplied with S.S. wire mesh shelves. 
Temperature controlled by Microprocessor based Digital Temp Controller with PT 100 as sensor & safety thermostat.Temp Range : 5°C above ambient to 60°C accuracy ±0.5°C

Chamber sizeNo of Shelves
14" x 14" x 14"2
18" x 18" x 18"3
18" x 18" x 24"4
24" x 24" x 24"4
24" x 24" x 36"5

Optional Accessories
  • Forced Air circulating system with fan for better uniformity of Temperature
  • Electronic Digital Timer Range 0 to 999 minutes
  • RS 485 for PC communication with Software Meta Logger
  • Single Channel Data logger with printing arrangement

Bacteriological Lab Incubator - (SILBLI-01)

Bacteriological Lab Incubator - (SILBLI-01)
Double walled construction inner chamber made of Mild Steel /St.Steel and exterior G.I. Sheets powder coated. The gap between the two walls filled with glass wool insulation. Inner glass door and exterior metal door with magnetic gasket & lock. Supplied with G.I. wiremesh shelves.
Temperature Controlled by thermostat or by electronic digital temp controller cum indicator.Temperature Range : 37 °C to 60°C. accuracy ± 1°C

Chamber sizeNo of Shelves
12" x 12" x 12"2
14" x 14" x 14"2
18" x 18" x 18"3
18" x 18" x 24"4
24" x 24" x 24"4
24" x 24" x 36"5

Optional Accessories
  • Forced Air circulating system with fan for better uniformity of Temperature
  • S.S wiremesh shelves
  • Electronic digital timer range 0 to 999 minutes
  • RS 485 for PC communication with Software Meta-Logger
  • Single Channel Data logger with printing arrangement

Torsion of Rods Apparatus - (SISTRA-16)

Torsion of Rods Apparatus - (SISTRA-16)
  • Low cost effective teaching
  • Self contained
  • Bench mounted

Suspension Bridge Apparatus - (SISSBA-09)

Suspension Bridge Apparatus - (SISSBA-09)
Apparatus consists of two mild steel cables 0.5cm diameter in cross section and 150cm long, pinned to two supports 90cm apart situated symmetrically. One of the ends can be converted to a roller by applying a known load at the end with the help of suspended pulley system. Vertical loads can be applied at various points along the span of the beam. A dial gauge with 25mm travel (with a magnetic base) will be supplied with the apparatus. Apparatus will be supplied complete with a supporting stand and a set of weights.

Deflection of Beam Apparatus - (SISDBA-04)

Deflection of Beam Apparatus - (SISDBA-04)
The bench mounted apparatus has a steel base with support at ends. The supports can be fitted with knife edges or clamp plates. A steel beam and two load hangers are supplied together with two dial gauges for measuring beam deflections and slopes. This equipment is part of a ranged to both, demonstrate and experimentally confirm basic engineering principles. Great care has been given to each item so as to provide wide experimental scope without unduly complicating or compromising the design. Each piece of apparatus is self-contained and compact. Setting up time is minimal, and all measurements are made with the simplest possible instrumentation, so that the student involvement is purely with the engineering principles being taught. A complete instruction manual is provided describing the apparatus, its application, experimental procedure and typical test results.

Computerised Rockwell Cum Brinell Hardness Testing Machine - (SICMRHT-03) 

Computerised Rockwell Cum Brinell Hardness Testing Machine - (SICMRHT-03) 
  • Minimum Order Quantity: 1 Unit
  • Brand: Shambhavi

IS: 1586:2000 for Roackwell and superficial test. 13:2281:2005 for Brinell Hardness Test. Rockwell cum Brinell tests consists of forcing an indentor (Diamond Ball) into the surface of a test piece in two steps i.e.first with preliminary test force and thereafter with additional test force and then measuring depth of indentation after removal of addition test force (Remaining preliminary test force active) for measurement of hardness value. These machines are suitable for Rockwell cum Brinell tests. These are motorized digital Hardness Testers having LCD display for easy hardness measurement. The results are displayed in 0.1 Rockwell unit for more accurate measurement. Brinell Hardness measured by using microscope manually.

Additional Information:
  • Delivery Time: Ready stock
  • Packaging Details: Export worthy packing

Trinocular Research Microscope - (SIMARM-004)

Trinocular Research Microscope - (SIMARM-004)
Trinocular Research Microscope :- Having following optical combination. Objective : 4x 10x, 40x SL and 100x SL oil immersion. Eye Pieces : H6 x and WF 10x (paired) & P 7x for photomicrography. a) All Optics are best Indian. b) All optics are best Indian but imported 100x oil immersion.

Binocular Research Microscope - (SIMARM-003)

Binocular Research Microscope - (SIMARM-003)
Binocular Research Microscope :- having following optical combination. objective : 5x, 10x, 45x and 100x oil immersion. eye pieces : 5x, 10x, 15 x (paired). a) all optics are best indian. b) all optics are best indian but imported 100x oil immersion.

Monocular Research Microscope - (SIMARM-002)

Monocular Research Microscope - (SIMARM-002)
Monocular Research Microscope :- Having following optical combination. Objectives : 5x, 10x 45x and 100x oil immersion. Eye pieces : 5x, 10x, 15x.
a)  All optics are best Indian.
b)  All optics are best Indian but imported 100x oil immersion.

Mechanical Engineering Equipment

Mechanical Engineering Equipment
Fluid Mechanics Lab Equipment
Hydraulic Machines Lab. Equipment
Hydraulic Bench with Accessories

Structural & Applied Mechanics Lab

Structural & Applied Mechanics Lab
Apparatus for Verification Of Clarke's Maxwell Reciprocal Theorem
Behaviour Of Column and Struts Apparatus
Curved Member Apparatus
Deflection of Beam Apparatus
Elastically Coupled Beam Apparatus
Elastic Properties of Deflected Beam
Apparatus Shear Centre
Apparatus Suspension Bridge
Apparatus Portal Frame
Apparatus Redundant Joint
Apparatus Two Hinged Arch
Apparatus Unsymmetrical Bending
Apparatus Pinned Joint Model
Pinned Joint Model
Bending Moment & Shear Force Apparatus 
Torsion of Rods Apparatus

Advanced Research Microscopes

Advanced Research Microscopes
Advanced Research Microscopes:-
a) Research Microscopes are most advanced for analytic and research work in college, laboratories hospitals and research industries. 
b) It has flat structure of body and base for stability and sturdiness fitted with quadruple revolving nose piece having threads of international standard stage slze 135 x 120 mm. Co-axial controls for easy slide manipulation on both axis with graduation and verniers. Range of movement 80x50 mm condenser unit is having rack and pinion movement with abbe condenser na 1. 20 with iris-diaphram and filter holder 
c) The electronic built in base illumination system fitted with a halogen lamp of 6v, 20w, average life of the bulb is 2000 hours. Built in transformer, controlled by solid state electronic control knob. A plano concave reflector attachment can be easily replaced with substage illuminator assembly. Series is available in three different inclined observation heads, for conveniences. Monocular, binocular or trinocular observation head.

Additional Information:
  • Item Code: SIMARM-001

Trinocular Research Microscope

Trinocular Research Microscope
Trinocular Research Microscope :- Having following optical combination. Objective : 4x 10x, 40x SL and 100x SL oil immersion. Eye Pieces : H6 x and WF 10x (paired) & P 7x for photomicrography. a) All Optics are best Indian. b) All optics are best Indian but imported 100x oil immersion.

Additional Information:
  • Item Code: SIMARM-004

Monocular Research Microscope

Monocular Research Microscope
Monocular Research Microscope :-

Having following optical combination. Objectives : 5x, 10x 45x and 100x oil immersion. Eye pieces : 5x, 10x, 15x.
A)  All optics are best Indian.
b)  All optics are best Indian but imported 100x oil immersion.

Additional Information:
  • Item Code: SIMARM-002

Abel Flash Point Apparatus

Abel Flash Point Apparatus
Abel Flash Point Apparatus is suitable for determining the close cup flash point of Petroleum and mixtures according to IP 33 & IP 170 and also IS 1448 (Part I) 1985 (P:20). It is suitable for oils whose flashes below 70°C. It is supplied with oil cup, cover fitted with stirrer, thermometer socket S.S. Water Bath, Stand. An electric heater is fitted at bottom for operation on 220 Volts AC Circuits. Following Models are available:-
  • Abels Flash Point Apparatus electrical heating with Energy Regulator Control – Oil Test Jet.
  • Abels Flash Point Apparatus electrical heating with Energy Regulator Control & Concealed Hot Plate – Oil Test Jet
  • Abel Flash Point Apparatus with Regulator DIGITAL TEMP. INDICATOR
  • Abel Flash Point Apparatus with Regulator, DIGITAL TEMP. INDICATOR with geared FHP. Elect. Driven Stirrer (120 R.P.M)
  • Abel Flash Point Apparatus Temp. Range -18°C to +70°C with REFRIGERATION SYSTEM as per IP-70 with Oil Test Jet system. With digital temperature. Indicator and FHP motor stirrer.

Salient Features
  • OPTIONAL ACCESSORIES:
  • Abel Oil Cup Thermometer (-35 / 70 C x 0.5°C) IP 74 C 
  • Abel Water Bath Thermometer (-30 / 80 C x 0.5°C) IP 75 C
  • Polish Wooden case 
  • Spare cup for above Apparatus 
  • Spare top (Cover Assemble) with Shutter mechanism 
  • Spare Nichrome Heating element 
  • Pendulum for Measuring Time in Strokes 
  • Concealed Hot Plate with housing

Additional Information:
  • Item Code: AFP-01

Binocular Research Microscope

Binocular Research Microscope
Binocular Research Microscope :- having following optical combination. objective : 5x, 10x, 45x and 100x oil immersion. eye pieces : 5x, 10x, 15 x (paired). a) all optics are best indian. b) all optics are best indian but imported 100x oil immersion.

Additional Information:
  • Item Code: SIMARM-003

Viscometer

Viscometer
a) Viscometer college Pattern, Ostwald b) Viscometer, U-tube, BS/U Size: A,B,C,D,E,F,G,H c) Viscometer BS/U With Constant Certificate d) Viscometer Suspended level BS/IP/SL e) Viscometer Suspended Level with Constant Certficate f) Viscometer, Suspended Level Shortend, BS/IP/SL, (S) Sizes: 3,4,5,6,7,8,9 g) Viscometer, Suspended Level, Shortend with Constant Certificate h) Viscometers, Cannon-Fenske, For Transparent Liquids, BS/IP/CF Sizes: 25,50,100,150,200,300,350,400,450,500,600 i) Viscometer Cannon-Fanske U-Tube for Transparent liquid with Certificaet j) Viscometers, Cannon-Fenske, for Opaque Liquids, ASTM-D 445 Sizes: 100,150,200,300,400,450,500,600 k) Viscometer C/F for Opaque Liquid with constant Certificate l) Viscometers, U-Tube, Reverse Flow, BS/IP/Rf Sizes: 2,3,4,5,6,7,8,9,10,11 m) Viscometer reverse flow with Constant Certificate n) Viscometer, Falling Sphere Sizes: 25,40 o) Filtering Tubes Sizes: 10,20,30,40

Additional Information:
  • Item Code: SILGVSC-001

Hydraulic Tank Jacking System

Hydraulic Tank Jacking System

Approx. Rs 89,000 / Piece

  • Minimum Order Quantity: 10 Piece
  • Capacity: 1-10 Ton
  • Operating Mode: Manual, Automatic
  • Condition: New
  • Body Material: Steel
  • Color: Yellow, Red
  • Brand: Shambhavi
  • Material: Alloy Steel, Stainless Steel, Mild Steel
  • Effective Lifting Height: 3500 mm

Shambhavi impex offers a wide range of Jacking System to the patrons. These products are designed and developed as per the technical details provided by the client. The offered range of products is also widely demanded in the market and caters to the requirement of varied industries. All our products are developed in hard and fast compliance.

Pinned Joint Model - (SISPJM-14)

Pinned Joint Model - (SISPJM-14)
Model consists of hinged joints. Model will be able to demonstrate the qualitative behavior of the truss under load. As the members are very flexible, a compression member will easily show it's buckling i.e. it will curve out of plain. The tension member however remains straight and tight. The student will therefore have a visual picture of the type of stresses i.e. compressive or tensile that each member of truss will carry under various positions of the load. In case of pinned joint truss, the student will be able to observe that angle between members at each joint undergo a small change
View More Products »
X
Provide Us More Details
Purpose of Requirement:

Reselling End Use Raw Material

X

Looking for New Items ?

    country-ico

    We will contact you soon !

    Shekhar Narain

    (CEO)

    Shambhavi Impex

    Navi Mumbai, Maharashtra, India

    More Categories

    View All Categories »
    Send SMS
    Get Callback